“The foundation of your home is built on the walls. The weather out there will not be nice and you need to pay special attention to your house’s exterior walls. Painting your wall isn’t enough to make it waterproof. After dealing with rain, snow, wind, dust, and heat of the outside environment, the paint will start peeling off regardless of the cost.”

Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.

Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.

Step 1: Properly expose the outside part of the wall

To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.

Step 2: Thoroughly clean the walls

“The outer part of your home’s wall is usually covered with a lot of dust and dirt from the outside. To make sure the process is efficient, you need to clear the debris and dust thoroughly. The dirt and debris can be cleaned by using a broom, brush, or sandpaper. Then wash it through a power washer.”

Step 3: Check out for the cracks and fill them up

Cracks and holes can develop over time. Follow up the cleaning process with a thorough finding of all the cracks and holes on the wall to ensure proper weatherproofing. They should be filled up with cement.

Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.

All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.

The cement mixture seals the cracks properly. Remove the loose cement from the wall before applying the cement.

Step 4: Add a layer of cement waterproofing sealer

If you want to make sure your wall is waterproof, you need to apply cement. After applying the cement in the crevices, let it dry and then apply the waterproof paint on the exterior walls. Allow it to become wet after that.

Step 5: Pick the right water-proofer

There are a lot of products that are waterproof. You have to pick the right one for your wall. Pick the water-proofer based on whether the wall is concrete or silicate.

It is possible to choose between a silicate-based concrete sealer and a concrete waterproofing coating. You can add strength to your walls with a plaster waterproof Additive.

Step 6: Apply the water-proofer

The water-proofer should be applied with a roller or brush. If you want to apply more than one layer, you need to give a thin coat. Add the second coating after the first one has dried.

Step 7: Apply tar and heavy-duty membrane

If you want to add more strength to the layer, you need to use a tar-based pitch. On the exterior wall, apply it.

After that, you need to apply a heavy-duty plastic or rubber Membrane, which will ensure the proper care of your Walls.

Step 8: Consider adding gravel

The base for the trench needs to be below the footer. The drainage pipes will get adequate support from a gravel base. Gravel provides enhanced protection and is long- lasting.

You need to lay the drainage pipe-cover along with the gravel. Next to the footer, level the position of the gravel and then back-fill it. A covering for the pipe is required.

Step 9: Add a fabric barrier

The fabric barrier should be secured along with the pipe. A fabric barrier will prevent the formation of dirt and keep your system clean. Simply back-fill the trench and build the top of the dirt relatively high and allow it to settle for a while. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia

Conclusion:

Good waterproof gives your home a new life and strength to deal with weather related issues. Magicrete can help you with good solutions for your walls. At a very low and affordable price, Magicrete can provide you proper weatherproofing.

“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like”